Vestavan Pod

Mercedes-Benz Sprinter L2H2

Vestavan Pod fits the W906 and W907 Sprinter L2H2, with the factory cab partition left in place. Set the table by the rear doors during the day and make up the bed in the same spot at night. Remove both modules to get your load space back for work.

8 of 20 launch places left
€5,990Regular price €9,990

The package includes the front kitchen module, the rear seating and bed module, a sink and a rechargeable tap. The package excludes the loading stand with rollers, hob and fridge.

Estimated delivery if you confirm today

Ready in İzmir
About 3 weeks
Arrival in Europe
About 4 weeks including shipping

Your written quote confirms the delivery week before you pay the deposit.

Vestavan Pod seating layout inside a Mercedes-Benz Sprinter L2H2 with the rear doors open

Living space

Inside your Sprinter, day and night.

Table between two dark benches, facing the open rear doors of the Sprinter

Face-to-face seating

The table runs between two facing benches towards the rear doors. Open the doors to enjoy the view from where you sit.

Two-burner hob and round stainless-steel sink in the Sprinter’s light-coloured kitchen worktop

Sink and rechargeable tap

After a muddy walk, the round sink and rechargeable tap are within reach by the sliding door. The hob and fridge shown are outside the package.

View from the dark rear bed cushions towards the front kitchen and side curtain in the Sprinter

From seats to a bed

Lower the table between the facing benches. The four cushions fit side by side to make up the bed. View the bed plan and dimensions.

Technical dimensions

Inside the Sprinter: how much room is there?

The table and bed plan give approximate dimensions from the W907 3D design. Bed length is measured along the van and width from side to side. Worktop height is measured from the finished Pod floor.

Sleeping surface · length × width187 × 167 cm
Tabletop · long × short side87 × 62 cm
Worktop · length × maximum depth106.3 × 50.6 cm
Worktop height above finished floor94.6 cm
Rear seating unit · length190 cm
Rear unit width · loading / extended132 / 169 cm
Folded kitchen module Width × length × height133.2 × 108.3 × 172 cm
Folded seating module Width × length × height132 × 190 × 172.1 cm

The folded dimensions exclude the loading stand. At the first fitting we check the door clearance and the vehicle’s fixing points.

Sprinter bed plan, 187 cm along the van and 167 cm across
The four cushions in bed position, viewed from above

Loading and unloading

From load space to camper.

Two people can load the pieces separately. You can remove the kitchen unit, storage benches and table from the main blocks one by one. Two people can then load and unload the pieces without a stand. The workshop photos show the front and rear blocks being moved whole on a loading stand with rollers. The stand is outside the package.

Fitting and removing the Pod in a Ducato · Fiat Ducato L3H2The bed dimensions in the film are for the Ducato. See the Sprinter dimensions. The hob and fridge shown are sold separately.
  1. Where the loading stand meets the Sprinter’s rear threshold

    Prepare to load through the rear doors

    The stand is lined up with the loading sill. The rear seating block is loaded in its narrow position. In the W907 design it is approximately 132 cm wide at this stage.

  2. Kitchen module sliding into the Sprinter from the loading stand

    Kitchen at the front, seating at the rear

    The front kitchen module sits behind the cab partition and the seating module follows. In the W907 design the rear block extends by 18.5 cm on each side to approximately 169 cm wide.

  3. Empty Sprinter load space with the furniture modules outside

    Back to work

    Fold the seating unit back to its narrow width. Unload the rear module onto the stand first, then the kitchen. The original cab partition stays in the van.

At the first fitting we check the clear rear opening, sill height, existing trim and suitable fixing points. Secure the modules and all moving parts before driving.

Before you order

Package and delivery.

What is included in the €5,990 launch package?

This layout fits both the W906 and W907 Mercedes-Benz Sprinter L2H2. The price covers the front kitchen, the rear seating and bed module, a sink and a rechargeable tap. First fitting and a handover demonstration at our İzmir workshop are included. The loading stand, hob and fridge are outside the package.

How can I store the modules outside the van?

You can store the kitchen unit, storage benches and table separately. To keep both blocks intact, use the folded module dimensions to work out how much garage space you need.

How is delivery in Europe priced?

We prepare a written quote for your country and city. It lists transport, on-site fitting if requested, applicable VAT, any customs charges and who pays each cost. When your Pod is ready, we send you a video and the dispatch date. The balance is payable before dispatch.

8 of 20 launch places left

A launch offer for your van.

Your free written quote sets out the earliest delivery week we can offer you and the total price. The launch price applies to the first 20 confirmed orders across the Ducato and Sprinter models. Once you accept the €5,990 package, you pay a deposit of €1,797 (30%) for your order. In İzmir, we fit the modules in your van and show you how to use them. You pay the remaining €4,193 (70%) at the workshop before collecting your vehicle. Ordering and delivery details

Other Pod modelFiat Ducato L3H2